How to install, open and close your commercial cantilever umbrella
This guide covers the Revolvashade commercial cantilever umbrella: how to assemble it onto its base, how to open it, and how to close it again. It is written for the people who will actually use the umbrella day to day, so if you are a cafe owner, resort manager or installer, this is for you. The umbrella is heavy and the frame is powder coated, so plan on two people and a clear, soft surface to work on.
What you need
- Two people. One person can assemble the frame on the ground, but you need two to lift it onto the base and to open it the first time.
- A cordless (battery) drill with the 24 mm socket and extension rod supplied with the umbrella. The same 24 mm size fits the base nut and the canopy drive.
- A spanner or socket for the three beam bolts (sizes vary by model; they come in the box).
- Thread locker (Loctite) for the canopy bolts.
- A moving blanket or flattened cardboard to protect the powder coat.
Part 1: assembling the frame
- Unpack carefully. Open the carton and remove all packaging. If you use a blade, keep it away from the frame so you do not scratch the powder coat.
- Lay out the parts. Put the main mast and the diagonal beam on the ground on your blanket or cardboard, in the shape they will take when assembled (see the drawing below).
- Slot the beam into the mast. The diagonal beam slides into the socket at the top of the main mast. Line up the pre-drilled holes.
- Bolt them together. Fit the three bolts provided through the pre-drilled holes at the top of the mast and tighten them. The frame is now one rigid piece.
Part 2: mounting the frame on the base
- Lift the frame upright. With one person at each end, stand the frame up and carry it to the base. Keep the beam end high so it does not drag.
- Slot it over the base. Lower the bottom of the main mast over the installed base until it seats fully.
- Lock it down. Tighten the 24 mm nut at the bottom of the main mast. This is what holds the whole umbrella to the base, so make sure it is firm.
Part 3: fitting the canopy
- Raise the canopy. With the canopy still closed and strapped, lift it up to the end of the umbrella arm so the hub lines up with the bolt holes.
- Bottom bolt first, from the side. Fit the lower bolt through the side of the hub and tighten it.
- Top bolt second, from the front. Fit the upper bolt from the front and tighten it. We recommend a drop of thread locker on both bolts so they cannot vibrate loose.
Part 4: opening the umbrella
The commercial cantilever does not use a hand crank. Underneath the hub, at the centre of the canopy, there is a 24 mm socket drive (item 25 in Figure 2). Turning it one way with a battery drill on the supplied socket and extension rod spreads the arms and opens the canopy; turning it the other way collapses the canopy. The canopy does not lower; it stays at the same height and folds in on itself.
- Undo the strap that holds the closed canopy together.
- Lift the arms. One person (two if you have them) takes hold of the canopy arms and gently lifts them outward so there is room for someone to get underneath.
- Fit the drill. Put the 24 mm socket onto the drive under the hub, with the extension rod between the socket and the drill.
- Wind slowly. Run the drill at low speed and let the canopy open under its own control. Keep winding until the canopy is fully open, the screw is tight and the fabric is taut.
- Check the tension. Push up on the canopy between the arms. It should feel drum tight, not slack.
Part 5: closing the umbrella
Closing uses the same 24 mm socket drive under the hub, run in the opposite direction. Turning it with the battery drill collapses the canopy: the arms fold in towards the hub while the hub itself stays where it is at the end of the beam. A commercial cantilever should be closed and strapped whenever it is not in use and whenever strong wind is forecast.
- Clear the area. Move tables and chairs so the arms can come down without hitting anything.
- Fit the drill with the 24 mm socket to the drive under the hub, as you did to open it.
- Run the drill the other way. Use low speed. The fabric goes slack first, then the arms fold in towards the hub.
- Guide the arms in. As the canopy folds, have your second person gather the arms together so the fabric folds neatly against the hub and nothing gets caught.
- Strap it. Once fully closed, fit the strap around the canopy so it cannot blow open. Fit the storage cover if you have one.
Wind and weather
- Close and strap the umbrella when it is not in use and before any forecast storm or strong wind.
- Wind ratings are breaking points measured with the umbrella fully open, fabric taut and in free airflow. They are not a safe operating limit. Refer to the rating certificate supplied with your umbrella.
- Nearby buildings and walls can funnel wind and put far more load on the umbrella than the open-air rating suggests.
- Never leave the umbrella half open. It is at its weakest with the fabric slack.
Looking after it
- Check the three beam bolts, the two canopy bolts and the 24 mm base nut every few months and after any storm.
- Hose the canopy down and let it dry fully before closing it for long periods, to stop mould and mildew.
- Keep the 24 mm drive under the hub clean. If it becomes stiff, a light spray of dry lubricant is all it needs.
- If anything bends, cracks or will not wind, stop using the umbrella and contact us. Replacement parts and service are available from Revolvashade.
Questions about your commercial cantilever, or need someone to install it for you? Call 07 3889 6844 or email hello@revolvashade.com.
